Choosing racking looks simple until you compare quotes and find that prices differ by a large margin. The difference is usually not in the look of the rack. It lies in steel thickness, section design, bracing, finish and the load the rack is actually designed to carry. This guide explains what to decide, in what order, and what to ask your supplier.
The short answer
Match the system to how you store and pick your goods.
| If you store... | Consider |
|---|---|
| Palletised goods, many different products, forklift handling | Selective pallet racks |
| Large volumes of few products on pallets | Drive-in racking |
| Cartons and small items picked by hand, medium loads | Longspan shelving |
| Light to medium items, small budgets, changing sizes | Slotted angle racks |
| Products that customers browse | Supermarket display racks |
| Pipes, bars, timber, sheets | Cantilever racks |
| Not enough floor area but plenty of height | Mezzanine floors |
| Anything unusual | Customized solutions |
Step 1: Know your load
Load decides the rack. Write down the following before you speak to any supplier.
- Heaviest unit load. For pallets, the weight of the heaviest loaded pallet, including the pallet itself.
- Unit size. Pallet or carton dimensions, and stacked height.
- Load type. Evenly spread weight (UDL) is much easier on a shelf than a heavy point load such as a drum or machine part.
- Growth. If your pallets will get heavier next year, specify for that now.
A rack does not have one capacity. Capacity depends on beam length, the height of each level, and the frame. Ask for a capacity table for the exact configuration you are buying.
Step 2: Measure your space
- Clear height. Measure to the lowest obstruction, such as roof trusses, lights or sprinkler pipes, not to the roof sheet.
- Column positions and floor plan. Existing columns decide bay layout.
- Sprinklers and lighting. Keep the clearance your fire consultant specifies between the top of the stored goods and the sprinklers.
- Floor. Racks load the floor at small points. Check floor thickness and flatness, especially for tall racks.
Step 3: Match the rack to your handling equipment
Aisle width follows from the machine you use.
| Equipment | Typical working aisle |
|---|---|
| Hand pallet truck | 2.0 to 2.5 m |
| Counterbalance forklift | 3.0 to 3.8 m |
| Reach truck | 2.6 to 3.0 m |
| Very narrow aisle truck | 1.6 to 2.0 m |
Wider aisles waste floor area. Narrower aisles increase density but need suitable trucks and skilled drivers. Also check the maximum lift height and rated capacity of the machine at that height, because forklift capacity falls as the load rises.
Step 4: Understand your stock profile
- Many products, each in small quantity: favour selective racking, where every pallet is accessible.
- Few products in large batches: drive-in racking saves space.
- First in, first out: matters for food, pharma and anything with an expiry. Selective and drive-through racking support it.
- Fast picking of small items: shelving with a mezzanine or a pick zone works better than pallet racking.
Step 5: Compare steel and construction, not just price
When two quotes for the "same" rack differ, check these first.
- Steel thickness of uprights and beams. Thinner steel is cheaper and weaker.
- Section shape and size. Box beams and roll-formed uprights with stiffening carry more than plain angles of the same weight.
- Bracing. Frames need enough bracing for their height.
- Welds and holes. Consistent slot punching and clean welds show quality control.
- Base plates and anchoring. Should be included and specified.
- Finish. See our guide to steel thickness and racking finishes.
- Capacity plate and drawing. A reputable supplier states capacity in writing.
Step 6: Ask about design standards
Racks are structural products. Ask which design method the supplier follows and what the stated capacity is based on. Indian practice commonly refers to IS 800 for steel design, IS 875 for loads, and IS 801 or IS 811 for cold-formed sections. Many rack designers also refer to international rack codes such as EN 15512 or RMI MH16.1. Delhi NCR falls in Seismic Zone IV under IS 1893, so anchoring and bracing deserve attention there.
Step 7: Plan for safety
- Fix a load capacity plate on each bay.
- Protect uprights with column guards in forklift aisles.
- Use safety pins on every beam.
- Inspect regularly. Look for bent uprights, damaged beams and loose bolts. See our rack safety checklist.
- Train forklift operators, and never climb racks.
What affects the price of racking
- Steel weight. Racks are priced largely by steel used, so thicker sections and taller racks cost more.
- Load rating. Heavier duty needs stronger sections.
- Finish. Powder coating costs less than galvanising, which costs less to maintain in humid or outdoor places.
- Custom sizes and accessories.
- Distance and freight. Racks are bulky, so transport is a real part of the cost.
- Installation.
The cheapest rack per pallet position is not the cheapest rack if it fails. A safe, correctly specified rack pays for itself over many years.
What to send when you ask for a quote
- Pallet or carton size and heaviest weight
- Number of pallet positions or shelves needed
- Building clear height, floor area and column layout
- Forklift or handling equipment model
- Type of goods and how they are picked
- Indoor, outdoor, damp or cold storage
- Delivery city and target date
Frequently asked questions
How much load can a pallet rack hold?
It depends on the design. Typical beam levels carry about 1,000 to 4,000 kg per pair of beams, but the safe figure for your rack must come from a capacity table for its exact configuration.
Is powder coating enough?
For dry indoor warehouses, yes. For damp, coastal, outdoor or cold storage, consider galvanising.
Can I add levels to my rack later?
Often yes, if the uprights were designed for the extra load. Tell your supplier about expansion plans at the start.
Do I need a mezzanine or taller racks?
If your building is tall, tall racks are usually the cheapest way to add capacity. A mezzanine is better when you need a working floor for picking, packing or offices.
Send us your area, what you store and the weight per pallet or shelf. We will suggest a system and quote.
Get a quote